View AP17E070064A_7340790.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

page 1 of 11 ap17e.07.0064a specifcation part no. ap17e.07.0064a product name 17mm one stage gps active patch antenna module with front end saw filter feature 17mm*17mm*6.3mm 64mm 1.13 ipex mhfi wide voltage 1.8v~5.5v 15db lna tested in free space rohs compliant spe-11-8-144/b |
page 2 of 11 the ap.17e is a one stage 17mm active patch antenna that has been designed specifcally for embedded (inside device) integration with gps receiver modules. the ap.17e combines a 17*17*4mm ad - vanced low profle ceramic patch antenna with a one stage lna and a front-end saw flter with ultra thin coaxial cable. it comes with its own integrated ground-plane. the front end saw flter reduces the risks where there is a cellular transmitter nearby of interference from out of band frequen - cies which can cause lna burn-out, satu - ration, or radiated spurious emissions. the antenna can work on a wide input voltage from 1.8v to 5.5v with best in class power consumption fgures. if further tuning and optimization specifc to a customer device is required taoglas offers a custom tuned and optimized part service. contact sales@taoglas.com for more information. cables and connectors can be customized according to request. 1. introduction antenna saw filter lna i-pex + cable spe-11-8-144/b |
page 3 of 11 2. specifcation 2.1 patch antenna 2.2 lna parameter specifcation frequency 1575.42 1.023mhz gain @ zenith -1.0dbic typ. @ zenith polarization rhcp axial ratio 3.0db max @ zenith patch dimension 17*17*4mm parameter specifcation frequency 1575.42 1.023mhz outer band attenuation f0=1575.42mhz f030mhz 2db min. f050mhz 18db min. f0100mhz 25db min. output impedance 50 output vswr 2.0 max pout at 1db gain compression point typ. -2dbm min. -6dbm lna gain, power consumption and noise figure voltage lna gain (typ) power consumption(ma) typ noise figure typ min. 1.8v 13db 1.6ma 2.5db typ. 3.0v 16db 3.5ma 2.5db max. 5.5v 17db 7.6ma 2.6db parameter specifcation rf cable coaxial cable ? 1.13 0.1mm, length 64mm 2.5mm connector ipex mhfi (u.fl) 2.3 cable* & connector spe-11-8-144/b |
page 4 of 11 3. lna gain and out band rejection @3.0v cg1 tr1 s21 > 1 1.5754200 ghz 16.111 db cg1 tr1 s21 2 1.6054200 ghz -27.059 db cg1 tr1 s21 3 1.5454200 ghz 12.455 db cg1 tr1 s21 4 1.6254200 ghz -34.597 db cg1 tr1 s21 5 1.5254200 gh -3.4458 db cg1 tr1 s21 6 1.6754200 ghz -20.195 db cg1 tr1 s21 7 1.4754200 ghz -10.158 db 1 tr1 s21 log mag 10.00db/ ref -40.00db (f2) 1 center 1.57542 ghz span 400 mhz 2/8 cor ifbw 500 khz 30.00 20.00 10.00 0.000 -10.00 -20.00 -30.00 -40.00 -50.00 -60.00 -70.00 >1 1.5754200 ghz 16.111 db 1 5 7 4 6 3 2 spe-11-8-144/b |
page 5 of 11 4. lna noise figure @3.0v 5. total specifcation (through antenna, lna, cable and connector) parameter specifcation frequency 1575.42 1.023mhz gain at 3v: 15 3dbic @ 90 output impedance 50 polarization rhcp output vswr max 2.0 operation temperature -40c to + 85c storage temperature -40c to + 85c relative humidity 40% to 95% input voltage min. 1.8v, typ. 3.0v, max. 5.5v antenna 17*17*6.1mm 1 40.00 gain scale/ 5.000 db -10.00 mkr1 1.5754 ghz 2.431 db 15.270 db center 1.57542 ghz bw 4 mhz points 11 span 3.00 mhz tcold 296.50 k avgs off att 0/ - - db loss off corr 9.000 nfig scale/ 1.000 db -1.000 1 spe-11-8-144/b |
90 270 180 0 2 -5 -10 -15 -20 -25 -30 -35 -40 +z +x page 6 of 11 6. radiation patterns 6.1 xz plane radiation pattern model no. test mode freq (mhz) max gain(dbi) min gain(dbi) avg. gain(dbi) source polar. date 1 ap17e.07.0064a xz 1575.42 -0.88 / 20.00 -8.25 / 244.00 -4.01 rhcp 2011/9/9 spe-11-8-144/b |
90 270 180 0 2 -5 -10 -15 -20 -25 -30 -35 -40 +z +y page 7 of 11 6.2 yz plane radiation pattern model no. test mode freq (mhz) max gain(dbi) min gain(dbi) avg. gain(dbi) source polar. date 1 ap17e.07.0064a yz 1575.42 -1.01 / 4.00 -19.77 / 118.00 -5.35 rhcp 2011/9/9 spe-11-8-144/b |
90 270 180 0 2 -5 -10 -15 -20 -25 -30 -35 -40 page 8 of 11 6.3 xy plane radiation pattern model no. test mode freq (mhz) max gain(dbi) min gain(dbi) avg. gain(dbi) source polar. date 1 ap17e.07.0064a xz 1575.42 -0.88 / 20.00 -8.25 / 244.00 -4.01 rhcp 2011/9/9 2 ap17e.07.0064a yz 1575.42 -1.01 / 4.00 -19.77 / 118.00 -5.35 rhcp 2011/9/9 spe-11-8-144/b |
page 9 of 11 7. technical drawing this drawing and its inherent design concepts are property of taoglas. not to be copied or given to third parties without the written consent of taoglas. tw design centre ipex mhf 1 "a" a all initial design kiwi 2011/10/20 top side bottom note: 1.soldered area 2.shielding case 3.double sided adhesive 4.the connector position has special orientation to the pcb as per drawing. 5.all material must be rohs compliant. 6.open/short qc, vswr required. name material finish qty ap.17e patch (17*17*4mm) ceramic clear 1 1 1 1 fep gray 2 3 gold plated brass 1.13 coaxial cable ipex mhf1 connector 1 4 tin plated tin (spte) shielding case 1 5 green fr4 0.8t pcb p/n ap.17e od.113.cm ipex.mhfi.113 1 6 white liner nitto 5015 double sided adhesive ap.17e name p/n material finish qty ap.17e patch (17*17*4mm) ceramic clear 2 1.13 coaxial cable od.113.cm gray 3 ipex mhf1 connector ipex.mhfi.113 brass gold plated shielding case tin (spte) tin plated 5 pcb fr4 0.8t green note: 1. soldered area 2. shielding case 3. double sided adhesive 4. the connector position has special orientation to the pcb as per drawing. 5. all material must be rohs compliant. 6. open/short qc, vswr required. this drawing and its inherent design concepts are property of taoglas. not to be copied or given to third parties without the written consent of taoglas. tw design centre ipex mhf 1 "a" a all initial design kiwi 2011/10/20 top side bottom note: 1.soldered area 2.shielding case 3.double sided adhesive 4.the connector position has special orientation to the pcb as per drawing. 5.all material must be rohs compliant. 6.open/short qc, vswr required. name material finish qty ap.17e patch (17*17*4mm) ceramic clear 1 1 1 1 fep gray 2 3 gold plated brass 1.13 coaxial cable ipex mhf1 connector 1 4 tin plated tin (spte) shielding case 1 5 green fr4 0.8t pcb p/n ap.17e od.113.cm ipex.mhfi.113 1 6 white liner nitto 5015 double sided adhesive ap.17e spe-11-8-144/b |
page 10 of 11 8. plugs usage precautions (1) to disconnect connectors, insert the end portion of i-pex under the connector fanges and pull off vertically, in the direc - tion of the connector mating axis. (2) to mate the connectors, the mating axes of both connectors must be aligned and the connectors can be mated. the click will confrm fully mated connection. do not attempt to insert on an extreme angle. after the connectors are mated, do not apply a load to the cable in excess of the values indicated in the diagram below. 8.1 mating / unmating 8.2 pull forces on the cable after connectors are mated 2 1 coaxial cable plug pulling tool p/n : 90192-001 receptacle plug rece 2n max. 2n max. 4n max. coaxial cable spe-11-8-144/b |
page 11 of 11 9. packaging spe-11-8-144/b |

▲Up To Search▲

Price & Availability of AP17E070064A

	To Download AP17E070064A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .